TPMS DIAGNOSTIC INFORMATION – Dodge Charger 2006-2020

10.07.2019

dodge charger - new

After the TREAD Act was mandated in 2007, all vehicles manufactured in the United States beginning in 2008, must be installed with direct or indirect TPMS systems.

The Dodge Charger uses a direct TPMS system, which means TPMS sensors are installed in the wheel. If one or more tires indicate low tire pressure, the TPMS sensors will transfer the information to the vehicle’s ECU. An indicator light (low-line TPMS system) or each tire pressure will show on the dash (high-line TPMS system).

When a sensor is replaced in one or more tires of a Dodge Charger, an OBD TPMS relearn is recommended to write the IDs to the vehicle’s ECU.

Dodge Charger Infographic

 

Type of TPMS system:

  • Direct TPMS, sensors are installed in the wheel
  • All OE and aftermarket TPMS part numbers and service kit replacement options for the Dodge Charger can be found in the VT56, VT55, and VT36 TPMS Tools in “Service TPMS”.

Type of TPMS frequency:

  • 315 MHz for years 2006-2007
  • 433 MHz for years 2008-2020

Type of Relearn procedures:

  • Bonus OBD relearn procedure coverage as an option on the VT56 requires OBD module (for years 2006-2017)
  • Manual (stationary) relearn (for years 2006-2020) 

Type of TPMS tool required for TPMS reset

  • TPMS scan tool with OBD module (VT56, VT46 brands)
  • TPMS activation tool combined with a Diagnostic Scan Tool (VT15, VT31, VT36, VT46 branded tools)

OBD relearn procedure, years 2006-2017:

  • OBDII dongle is required
  • Confirm TPMS sensors are properly installed
  • Adjust tire pressures to placard value
  • Hold TPMS tool on left front tire sidewall next to the valve stem
  • Repeat for the right front, right rear and left rear tires
  • Apply OBD module to the DLC
  • Turn ignition ON
  • Press OK on TPMS tool to transfer sensor data to the ECU
  • Disconnect OBD module from DLC
  • Turn ignition OFF, then ON
  • Drive for at least 5 minutes at 28mph

 

Nissan OBDII Relearn 1 RAM OBDII Relearn 2

Manual (Stationary) relearn procedure, years 2006-2020:

  • OBDII connector is not required 
  • Confirm TPMS sensors are properly installed 
  • Adjust tire pressures to placard value 
  • Activate sensors with TPMS Tool 
  • Drive vehicle for up to 20 minutes about 15 mph or until TPMS light is off 

RAM Manual Relearn

Troubleshooting tips

System Fault Issues

If a system fault is detected, the TPM Telltale Light will flash on and off for 75 seconds and then remain on solid. The system fault will also sound a chime. If the ignition switch is cycled, this sequence will repeat, providing the system fault still exists. The TPM Telltale Light will turn off when the fault condition no longer exists. A system fault can occur due to any of the following:

  1.  Signal interference due to electronic devices or driving next to facilities emitting the same radio frequencies as the TPM sensors.
  2. Installing aftermarket window tinting that contains materials that may block radio wave signals.
  3.  Accumulation of snow or ice around the wheels or wheel housings.
  4. Using tire chains on the vehicle.
  5.  Using wheels/tires not equipped with TPM sensors.

TPMS DTC code information

Use the VT56 to retrieve Dodge TPMS DTC codes by selecting the “Service” icon. After selecting the Make, Model, and Year select the DTC code icon. Use the OBDII module to retrieve the Dodge DTC TPMS information to diagnose and service the TPMS issues determined.